الأشكال الموجية The Waveforms

[هيسبيريدس]

الأشكال الموجية The Waveforms

الشكل الموجي The Waveform هو شكل وهيئة الإشارة - أو الاتجاه الذي يأخذه منحناها إما بالزيادة أو النقصان - التي تنتشر بشكل موجة ، سواء كانت موجة مائية على سطح الماء أو موجة اهتزازية على وتر مرن. وفي بعض النصوص - الكتب والمقالات...الخ - يتم استخدام كلمة الشكل الموجي للتعبير عن شكل المنحنى لأي كمية تتغير بالنسبة للوقت مجازيا وذلك بالاعتماد على التعريف السابق.

Introduction to Waveforms
The oscillators are electronic circuits which are used to generate a continuous output signal at some predetermined frequency. There are many different types of oscillator circuits available but generally they all consist of an amplifier and either an Inductor-Capacitor, (LC) or Resistor-Capacitor, (RC) tank circuit used to produce a sine wave type output signal. But sometimes in electronic circuits we need to produce many different types and shapes of Signal Waveforms such as Square, Rectangular Triangular or Sawtoothed type waveforms that can be used for either timing signals, clock signals or as trigger pulses. However, before we can begin to look at how the different types of waveforms are produced, we firstly need to understand the basic characteristics of a Waveform.

Technically speaking, Waveforms are basically a visual representation of the variation of a vol***e or current over time. In plain English this means that if we plotted these vol***e or current variations on graph paper against a **** axis of time, (t) the resulting plot or drawing would represent the shape of a Waveform. There are many different types of waveforms available but they can all be broken down into two distinctive groups.

• 1. Uni-directional Waveforms - these waveforms are always positive or negative in nature flowing in one forward direction only as they do not cross the zero axis point. Common uni-directional waveforms include Square-wave timing signals, Clock pulses and Trigger pulses.

• 2. Bi-directional Waveforms - these waveforms are also called alternating waveforms as they alternate from a positive direction to a negative direction constantly crossing the zero axis point as they go through periodic changes in amplitude, with the most common by far being the Sine-wave.

Whether the waveform is uni-directional, bi-directional, periodic, non-periodic, symmetrical or non-symmetrical they all include the following three common characteristics:

• 1). Period: is the length of time in seconds that the waveform takes to repeat itself from start to finish. This can also be called the Periodic Time of the waveform for sine waves, or the Pulse Width for square waves.

• 2). Frequency: is the number of times the waveform repeats itself within a one second time period. Frequency is the reciprocal of the time period, ( ƒ = 1/T ) with the unit of frequency being the Hertz, (Hz).

• 3). Amplitude: is the magnitude or intensity of the signal waveform measured in volts or amps.


Periodic Waveforms
Periodic waveforms are the most common of all the waveform types as it includes Sine Waves. The AC (Alternating Current) mains waveform in your home is a sine wave and one which constantly alternates between a maximum value and a minimum value over time with the length of time it takes between each individual repetition or cycle being known as its "Periodic time" or simply the Period of the waveform. Then this period can vary with each waveform from fractions of a second to thousands of seconds. For example, a sine wave which takes 1 second to complete will have a periodic time of 1 second, likewise a sine wave which takes 5 seconds to complete will have a periodic time of 5 seconds and so on.

So, if the length of time it takes for the waveform to complete one full pattern or cycle before it repeats itself is known as the "period of the wave" and is measured in seconds, we can then express the waveform as a Period number per second denoted by the letter T as shown below.

A Sine Wave Waveform

Units of periodic time, (T) include: Seconds (S), milliseconds (mS) and microseconds (μS). For sine wave waveforms only we can also express periodic time in degrees or radians, as one full cycle is equal to 360o (T = 360o) or in Radians as 2π (T = 2π), then 2π = 360o - ( Remember this! ).

We now know that the time it takes for a waveform to repeat itself is known as the periodic time or period which represents a fixed amount of time. If we take the reciprocal of the period, ( 1/T ) we end up with a value that denotes the number of times a period or cycle repeats itself in one second or cycles per second, and this is commonly known as Frequency with units of Hertz, (Hz). Then Hertz can also be defined as "cycles per second" and 1Hz is exactly equal to 1 cycle per second.

Both Period and Frequency are mathematical reciprocals of each other and as the periodic time of the waveform decreases, its frequency increases and vice versa with the relationship between Periodic time and Frequency given as.

Relationship between Frequency and Periodic Time

Where: f is in Hertz and T is in Seconds.

One Hertz is exactly equal to one cycle per second, but one hertz is a very small unit so prefixes are used that denote the order of magnitude of the waveform such as kHz, MHz and even GHz.

Square Wave Waveforms
Square wave Waveforms are used extensively in electronic and micro electronic circuits for clock and timing control signals as they are symmetrical waveforms of equal and square duration representing each half of a cycle and nearly all digital logic circuits use square wave waveforms on their input and output gates. Unlike sine waves which have a smooth rise and fall waveform with rounded corners at their positive and negative peaks, square waves on the other hand have very steep almost vertical up and down sides with a flat top and bottom producing a waveform which matches its de******ion, - "Square" as shown below.

A Square Wave Waveform

We know that square wave waveforms are symmetrical in shape as each half of the cycle is identical, so the time that the pulse width is positive must be equal to the time that the pulse width is negative or zero. When square wave waveforms are used as "clock" signals in digital circuits the time of the positive pulse width is known as the "Duty Cycle" of the period. Then we can say that for a square wave waveform the positive or "ON" time is equal to the negative or "OFF" time so the duty cycle must be 50%, (half of its period). As frequency is equal to the reciprocal of the period, ( 1/T ) we can define the frequency of a square wave waveform as:

Example No1
A Square Wave waveform has a pulse width of 10mS, calculate its frequency.
For a Square wave waveform, the duty cycle is given as 50%, therefore the period of the waveform must be equal to: 10mS + 10mS or 20mS

So to summarise, Square wave Waveforms are symmetrical in shape and have a positive pulse width equal to the negative pulse width resulting in a 50% duty cycle. Square wave waveforms are used in digital systems to represent a logic level "1", high amplitude and logic level "0", low amplitude. If the duty cycle of the waveform is any other value than 50% the resulting waveform would then be called a Rectangular Waveform or a Pulse.
.

[هيسبيريدس]

Rectangular Waveforms
Rectangular Waveforms are similar to the square wave waveform above, the difference being that the two pulse widths of the waveform are of an unequal time period. Rectangular waveforms are therefore classed as "Non-symmetrical" waveforms as shown below.


A Rectangular Waveform

The example above shows that the positive pulse width is shorter in time than the negative pulse width. Equally, the negative pulse width could be shorter than the positive pulse width, either way the resulting waveform shape would still be that of a rectangular waveform. These positive and negative pulse widths are sometimes called "Mark" and "Space" respectively, with the ratio of the Mark time to the Space time being known as the "Mark-to-Space" ratio of the period and for a Square wave waveform this would be equal to one.

Example No2
A Rectangular waveform has a positive pulse width (Mark time) of 10mS and a duty cycle of 25%, calculate its frequency.

The duty cycle is given as 25% or 1/4 and this is equal to 10mS, then the period of the waveform must be equal to: 10mS (25%) + 30mS (75%) which equals 40mS (100%) in total.

Rectangular Waveforms can be used to regulate the amount of power being applied to a load such as a lamp or motor by varying the duty cycle of the waveform. The higher the duty cycle, the greater the average amount of power being applied to the load and the lower the duty cycle, the less the average amount of power being applied to the load and an excellent example of this is in the use of "Pulse Width Modulation" speed controllers.


Triangular Waveforms
Triangular Waveforms are generally bi-directional non-sinusoidal waveforms that oscillate between a positive and a negative peak value. Although called a triangular waveform, the triangular wave is actually more of a symmetrical linear ramp waveform because it is simply a slow rising and falling vol***e signal at a constant frequency or rate. The rate at which the vol***e changes between each ramp direction is equal during both halves of the cycle as shown below.

A Triangular Waveform

Generally, for Triangular Waveforms the positive-going ramp or slope (rise), is of the same time duration as the negative-going ramp (decay) giving the triangular waveform a 50% duty cycle and for a given vol***e amplitude the frequency of the waveform will determine the average vol***e level of the wave, as a slow rise and slow delay time of the ramp will give a lower vol***e level than a fast rise and decay time. However, we can produce non-symmetrical waveforms by varying either the rising or decaying ramp values to give us another type of waveform known commonly as a Sawtooth Waveform.


Sawtooth Waveforms
Sawtooth Waveforms are another type of periodic waveform. As its name suggests, the shape of the waveform resembles the teeth of a saw blade. Sawtoothed waveforms can have a mirror image of themselves, by having either a slow-rising but extremely steep decay, or an extremely steep almost vertical rise and a slow-decay as shown below.

Sawtooth Waveforms

The positive ramp Sawtooth Waveform is the more common of the two waveform types with the ramp portion of the wave being almost perfectly linear. The Sawtooth waveform is commonly available from most function generators and consists of a fundamental frequency (ƒ) and all its integer ratios of even harmonics only, 1/2, 1/4, 1/6 1/8 ... 1/n etc. What this means in practical terms is that the Sawtoothed Waveform is rich in harmonics and for music synthesizers and musicians gives the quality of the sound or tonal colour to their music without any distortion.


Triggers and Pulses
Although technically Triggers and Pulses are two separate waveforms, we can combine them together here, as a "Trigger" is basically a very narrow "Pulse". The difference being a trigger can be positive or negative in direction were as a pulse is only positive in direction. A Pulse Waveform or "Pulse-train" as they are more commonly called, is a type of non-sinusoidal waveform that is similar to the Rectangular waveform we looked at earlier. The difference being that the exact shape of the pulse is determined by the "Mark-to-Space" ratio of the period and for a pulse or trigger waveform the Mark portion of the wave is very short with a rapid rise and decay shape as shown below.

A Pulse Waveform

A Pulse is a waveform or signal in its own right. It has very different Mark-to-Space ratio compared to a high frequency square wave clock signal or even a rectangular waveform. The purpose of a "Pulse" and that of a trigger is to produce a very short signal to control the time at which something happens for example, to start a Timer, Counter, Monostable or Flip-flop etc, or as a trigger to switch "ON" Thyristors, Triacs and other power semiconductor devices.


Function Generator
A Function Generator or sometimes called a Waveform Generator is a device or circuit that produces a variety of different waveforms at a desired frequency. It can generate Sine waves, Square waves, Triangular and Sawtooth waveforms as well as other types of output waveforms. There are many "off-the-****f" waveform generator IC's available and all can be incorporated into a circuit to produce the different periodic waveforms.

One such device is the 8038 a precision waveform generator IC capable of producing sine, square and triangular output waveforms, with a minimum number of external components or adjustments. Its operating frequency range can be selected over eight decades of frequency, from 0.001Hz to 300kHz, by the correct choice of the external R-C components.

Waveform Generator IC

The frequency of oscillation is highly stable over a wide range of temperature and supply vol***e changes and frequencies as high as 1MHz is possible. Each of the three basic waveform outputs, sine, triangle and square are simultaneously available from independent output terminals. The frequency range of the 8038 is vol***e controllable but not a linear function. The triangle symmetry and hence the sine wave distortion are adjustable.

The sources:
موسوعة ويكيبيديا
Electronics-Tutorials.ws

For more information check these sites:

http://www.doctronics.co.uk/signals.htm
For: Signals and Waveforms

http://hep.physics.indiana.edu/~rick...waveforms.html
For: Complex Waveforms

http://en.wikipedia.org/wiki/Waveform
For: Waveforms
.